Clean your radiators and remove rust in just 3 steps

With the arrival of the final months of the year, the climate changes begin to arrive, accompanied by a much lower temperature that makes us have to take refuge in certain devices to heat our home, as is the case with the heating.

The use of this is the most common, especially in those areas where temperatures in winter are quite low. But, for our heating to work at full capacity during this time, it is necessary that we have previously checked that all the elements that are part of it work correctly.

In this sense, the radiators are one of the devices that is necessary clean up before putting them into use and today we are going to tell you how to do it because it will depend on the type of radiator you have. So if you want to know what is the best method for clean up your radiatorIt is best that you continue reading.

The best methods to clean the radiators of your house

The Heating systems They are made up of different elements such as oil boilers or gas, the circuit that carries the hot water and, of course, the radiators. With respect to the latter, they are the most visual element and the one that, therefore, is seen more exposed to environmental pollution.

That is why it is essential that we keep them very clean and, then, we are going to explain the 3 crucial steps to clean your radiators and they are perfect. Take note!

1. Clean your radiator inside and out

As you well know, the radiators they usually have many nooks and crannies, some of which are quite small and quite complex to clean. For this reason, the first piece of advice we are going to give you is to turn to a small fine bristle brush to help you during the cleaning process. Take the opportunity to put the brush through all those holes, turning it to reach the most hidden areas.

If you use a brush with semi-hard hair, the dust that has been accumulating in these areas will fall to the ground and then you can use a vacuum cleaner to collect excess dirt.

Once you have removed the dust that was on the surface, you may find that there is still residual dirt accumulated that needs cleaning. deeper cleaning. So that you don’t get too complicated, the best thing you can do is moisten the brush with a mixture of soap and water
then pass it gently over the radiators, being careful not to damage them.

The really important thing in this regard is that you clean them always with the heating off and when the radiators are cold. Also, it is important that you wait until they are completely dry before turning the heating back on.

2.Remove rust from the radiator

Although it is not something that always happens, sometimes the radiators tend to accumulate traces of rust that can impair its operation and that is why it is important that we remove them quickly.

To do this, it is best to rub the radiator with sandpaper or with a special steel brush that allows us to get rid of the rust that has accumulated in the area. Of course, we advise you to first cover the wall and the floor so that stains do not occur in these areas.

You will see how a kind of accumulated rust dust begins to fall, which you can remove with the help of a dryer or a vacuum cleaner. You will have to repeat this process until you have thoroughly removed all the rust that has accumulated on the different radiators in your house.

3. Apply a product for the final finish

So that this does not happen again or if you need to remove the most difficult stains, you can buy a rust transformer And give the radiator a couple of hands. In this way you will prevent the rust from accumulating again on the surface of it and you will make it better resist the passage of time.

Once you have done it, you will only have to clean it with denatured alcohol and give it a product that serves to protect it, such as beeswax. However, if you want to give it a more original and cheerful touch, you can also opt for paint your radiator with a heat resistant paint.

How to clean electric radiators

So far we have seen what is the way to clean the most classic cast iron radiators, but, what about electric radiators? Do they clean the same?

The truth is that the process is quite the same. The first thing we must do is clean the entire surface with the help of a antistatic cloth so that the dust stays stuck in it and it is not necessary for us to use the vacuum cleaner.

It is recommended that we clean this rag every so often to go removing excess dust that accumulates in it while we clean, otherwise we could dirty the surface even more and we would have to start the task again.

Also, in case you see any stain, we recommend that you try to remove it with the help of a steam cleaner or using products specifically created for cleaning radiators that you can find in any supermarket.

Finally, let the radiator dry completely or do it yourself with the help of a completely dry, lint-free step. This step is essential because, until it is completely dry, you will not be able to turn on your heating system again.

As you can see, cleaning a radiator is a simpler task than it may seem at first, being something totally essential if we want our heating to work with the higher energy efficiency. We hope that this article has helped you to resolve any doubts you may have about it and remember carry out this task before the cold arrives.

Leave a Comment

Your email address will not be published.